Two engaging workshops will take place on Wednesday, 28 May 2025. When registering for the conference, you can choose to attend one.
See below for full workshop details and topics.
Join us on Wednesday, 28 May 2025, for an enriching pre-conference workshop day at the 2nd Southern African Geotechnical Conference (SAGC 2025).
About the Presenter Jamie Standing is Professor of Ground Engineering in the Department of Civil and Environmental Engineering at Imperial College London. His key research interests include laboratory testing of soils, unsaturated soil mechanics, full-scale field monitoring and instrumentation, and tunnelling and soil-structure interaction. He has more than 25 years’ experience of teaching at both undergraduate and post-graduate level, ranging from basic soil mechanics (seepage, consolidation, shear strength) to unsaturated soil mechanics and field monitoring and geotechnical processes. He is a chartered Civil Engineer, Fellow of the Geological Society, Associate of the Geotechnical Consulting Group and a member of three ISSMGE technical committees: TC204 (Underground Construction in Soft Ground); TC220 (Field Monitoring in Geotechnical Engineering) and TC301 (Preservation of Monuments and Historic Sites). He has always worked closely with industry and has run three major tunnelling research projects. From 2016 to 2021 he was a member of the International Board of Experts for Żelazny Most tailings dam. He has served on the BGA and BTS committees and been an editorial board member for Géotechnique and QJEGH. He has delivered numerous invited lectures and keynote addresses, including the Géotechnique lecture in 2009. Overview Historically the subject of soil mechanics was developed for saturated conditions where there were just two phases of solid and water. Soils in this condition are relevant to many applications especially in temperate climates. However, in many environments the water table is deep below the ground surface and the soil above it is not fully saturated, it has an additional air phase which has important implications on the soil response. Compacted fills and tailings also often fit into this category where pore water pressures are negative and so possess suction. The course (7 hours) will cover unsaturated soil mechanics, starting from basic principles such as surface tension, capillarity, relative humidity and then move on to soil response with three phases (solid, water, air). Unsaturated soils usually have negative pore water pressures, expressed as suctions. Soil water retention curves link suction with other variables such as degree of saturation and water content. The measurement and control of suction is discussed in detail along with its effect on the volumetric and shearing response of unsaturated soils. Conceptual models are developed linking suction with net stress, volume change and shear stress, accounting for collapsible and expansive soils. The basis of a constitutive model incorporating these elements is presented and practical implications of unsaturated soils are also covered. Handouts of the lecture slides and some typed lecture notes will be made available. On successfully completing this one-day course, delegates will: – have basic knowledge of where unsaturated soils are encountered; – be familiar with all basic terminology relating to unsaturated soils; – understand the effect of fabric on the response of consolidated soils, especially in expansive and collapsible soils; – differentiate between different types of suction; – be conversant with soil-water retention curves and appreciate their significance; – understand the effect of suction on volume change and shear strength behaviour; – know about various apparatus that enable unsaturated soils to be tested with and without suction control and measurement.
About the Presenter Dr. Reginald Hammah is the Chief Scientific Officer at Rocscience, a leading provider of geotechnical software solutions, and also serves as the Director of Rocscience Africa. He holds a Ph.D. in Civil Engineering with a specialization in Rock Mechanics from the University of Toronto, Canada, and a Masters degree from the Zaporozhye Industrial Institute, Ukraine. Dr. Hammah has played a pivotal role in advancing geotechnical engineering, particularly in Africa, and has been integral to Rocscience’s global expansion and technical leadership. He has served as Technical Chair for major industry conferences, such as the Rocscience International Conference, and is recognized for his expertise in geomechanics, numerical modelling, and risk management in mining and civil engineering. Dr. Hammah is also an accomplished editor and contributor to technical publications in the field. Introduction This one-day course will focus on Rocscience’s newest cutting-edge software, RSWall, and how it integrates with Slide2. The combination of these two programs enhances the ability of geotechnical engineers to design and analyze retaining walls. Course overview Participants will gain hands-on experience with RSWall, a new retaining wall design software that evaluates the stability of retaining walls to ensure long-term durability. They will practice assessing the stability of retaining walls such as MSE walls using AASHTO, Eurocode, British Standards, or AS 4678. The course will then integrate RSWall analysis with Slide2, the industry-leading 2D limit equilibrium analysis software for evaluating slope stability, safety factors, and the probability of failures. Key Learning Objectives 1.Master RSWall’s capabilities for designing various retaining wall types 2.Understand the design workflow and automated report generation in RSWall 3.Learn to seamlessly integrate RSWall designs into Slide2 for overall slope stability analysis Course Details The course will discuss the design workflow that ensures that reinforced walls resist lateral earth pressures while maintaining equilibrium. The discussion will cover the analysis of the sliding, overturning, bearing capacity, and internal stability of walls using industry-recognized methods. The course will describe the RSWall software interface and details of the following workflow for designing and analyzing walls in the program: 1.Establishing project settings (selecting the applicable wall type, design standard and analysis methodology) 2.Defining wall profile(s) and segment(s) 3.Defining soil properties and assigning soil regions 4.Defining groundwater conditions (if applicable) 5.Assigning loading and support to wall segments 6.Computing and reviewing results 7.Generating report figures and hand calculations 8.Exporting RSWall models to Slide2 9.Computing and analyzing overall slope stability results in Slide2 Participants will participate in the following practical exercises: 1.Designing a complex retaining wall using RSWall 2.Importing an RSWall design into Slide2 for further analysis 3.Performing 2D slope stability analysis with retaining wall structures and 4.Applying Slide2’s advanced features for seepage analysis and support design This course is ideal for practising engineers, academics, and students looking to enhance their geotechnical engineering skills and leverage the full potential of Rocscience’s software suite for retaining wall design and slope stability analysis.